Việt Nguyên Co.,Ltd Cung cấp chuyên nghiệp dây chuyền sản xuất tấm xốp XPE, IXPE và xốp tấm EPE cũng như các thiết bị phụ trợ cho ngành xốp PE.
Dưới đây chúng tôi xin giới thiệu về dây chuyền chuyên dụng sản xuất xốp tấm XPE.
QUOTATION
报价书
XPE 发泡板生产线
XPE foam board Line
The photos in this quotation are only for reference purpose, the real machine will vary due to different customerised requirements.图片仅作参考,实际机械根据不同要求而变
Object 项目 |
XPE 发泡板生产线
XPE foam board Line |
Price 价格 |
CIF VN |
Delivery 交货 |
goods loaded into container, packing included 货物装入集装箱, 包括包装 |
Delivery time 交货期 |
90 days from down payment receipt 收到预付款后 90 天 |
Payment 付款方式 |
30% down payment by T/T, 70% before shipping 预付 30%T/T, 装船前 70% |
Start-up 调试 |
included 包括 |
Warranty 质保 |
one year 一年 |
Validity 报价有限期 |
90 days 90 天 |
Seller reserves the right to make the technical modification in necessary condition.
我司保留对生产线技术改进的权利,以上规格参数如有变更,恕不另行通知。
Ⅰ、概述:
1、使用条件:380V/3 相/50Hz
2、使用材料:低密度聚乙烯,发泡剂,交联剂等 3、设备产量:最大 150-200Kg/h
4、交联聚乙烯(XPE)制品厚度:3~12mm,
母片厚度:1-4mm 5、交联聚乙烯(XPE)制品最大宽度:1600mm
6、整机的操作方向在右侧。
7、设备装机功率:330KW(动力功率约 132KW, 加 热 功 率 约 100KW) 8、设备耗水量:30m³/h(循环水)
9、设备耗气量(压缩空气):总用压缩空气量
约 为 1.5m³/h, 气 压 0.8MP 。 10、设备消气量:天然气约 25-35m³/h(主燃气管道DN65,燃气压力为 80-100Kpa;进燃烧器
Ⅰ、Overview:
1、electrical condition: 380V/3P/50Hz
2、Usage material:Low density polyethylene, foaming agent, crosslinking agent, etc
3、Max capacity:150-200Kg/h
4、The final product: 3~12mm,Mother piece:1-4mm
5、1600mm The max width of the final XPE sheet
6、The operating direction on the right side of the machine.
7、Install power:330KW(moving unit 132KW, heating unit 100KW)
8、Water circulation:30m³/h
9、Compressed air: about1.5m³/h,pressure 0.8MP
10、Foam gas consumption :natural gas about
支路管道,直径DN40)
11、设备机械线速度:母片 0.8-8m/min,发泡片材 5-20m/min Ⅱ、设备简介:
一、XPE150/28 型挤出机 :
1) 螺杆及料筒制作材料为 38CrMoALA,并经渗氮处理,螺杆直径Φ150,长径比 28:1,螺杆适合挤LDPE 粒料,挤出机最大产量为
160-200Kg/h。
螺杆渗氮深度为 0.4~0.6mm,硬度(HV)740~
940,表面粗糙度Ra≤0.8。
螺杆芯部需加钻深孔φ40,以便芯部通水冷却。螺杆芯部需加钻深孔到底,以便芯部通水冷却
2) 机筒渗氮深度为 0.6~0.7mm,硬度(HV)
≥940,内壁粗糙度Ra≤1.6,机筒外用水套式加强冷却效果。
机筒与齿轮箱之间加过渡短套,带密封装置。
3) 减速箱带强制冷却单元,硬齿面磨齿减速箱, 齿轮采用20CrMOTi 材料制作,并渗碳磨齿处理, 与电机采用联轴器传动。Reducer with forced
4) 主电机采用直流电机功率为 160KW,调速器采用 ABB 品牌调速器控制,温度表采用日本RKC 或欧姆龙表,PID 智能控制,测温元件采用铂电阻,控温精度为±1℃,施耐德接触器,其它小电器为国产名牌,并保证电气线路排列整齐,颜色分明,标号准确。
5) 测温点共 12 区,其中机筒 6 区,法兰、流道、模具预留 6 区,机筒采用陶瓷加热圈加热,加热圈通水冷却,螺杆芯部水冷却。电磁阀型号采用大一些。
25-35m³/h(main gas pipe DN65,gas pressure 80-100Kpa;branch pipe into firing unitDN40) 11 、 Design mechanical speed:master sheet 0.8-8m/min,foam sheet 5-20m/min
Ⅱ、Equipment introduction:
1. XPE150/28 Extruder :
1)Screw and cylinder production material for 38 CrMoAlA , and after nitriding process, screw diameter Φ150, length-diameter ratio 28:1, screw for LDPE granular materials, extrusion machine maximum yield of 160 -200kg/h
Screw nitriding depth of 0.4 ~ 0.6 mm, hardness (HV) 740 ~ 740, the surface roughness Ra 0.8 or less.
The screw core to drill deep hole φ 40, so that the core is cooled. The screw core to drill deep hole to the end, so that the core is cooled 2)Barrel nitriding depth of 0.6 ~ 0.7 mm, hardness (HV) 940 or higher, inner surface roughness Ra 1.6, or less water barrel outer shell to strengthen the cooling effect.
Barrel and the gear box and transition between short sleeve, sealing device.
3) Reducer with forced cooling unit, hard tooth surface gear grinding reducer, gear made of20 CrMoAlA materials and carburizing gear grinding processing, and motor USES the coupling transmission.
4) The main motor adopts DC motor, the power of 160 kw, speed governor control using ABB brand, adopt Japan RKC temperaturecontroller or omron meter, intelligent PID control, adopts platinum resistance temperature measurement
6)哈夫式模具法兰,带有摇臂式结构,以便快速打 开 模 具 。 7) 滤网的设计采用上海金纬紧闭方式
A. 中间滤网的实际图依供方所提供的标准参考
设计。沟槽并非在中间请注意此设计点.
B. 滤网前后各需加裝一只压力表
C. 滤网共配 3 块。